Home

• VMEbus
  • Brand Innovators B.V. BI-0316
    • Brand Innovators B.V. BI-0316 Block Diagram
    • manual/bi0316/book_2.htm
      • Chapter 1 General Information
      • manual/bi0316/book_1.htm
      • 1.1 Introduction
      • 1.2 Features
      • 1.2.1 SCSI Connectivity
      • 1.2.2 SCSI Daisy-Chaining
      • 1.2.3 One Slot Solution
      • 1.2.4 VMEbus Signals
      • 1.3 General Description
      • 1.4 Related Documents
      • Chapter 2 Functional Description
      • 2.1 Introduction
      • 2.2 Position Numbering
      • 2.3 SCSI Bus Technology
      • 2.3.1 Overview
      • 2.3.2 Data Transfer Options
      • 2.3.3 Electrical Options
      • 2.4 SCSI-2 and SCSI-3 Cabling Differences
      • 2.4.1 SCSI-2 Cabling
      • 2.4.2 SCSI-3 Cabling
      • 2.5 SCSI Bus Connection Options
      • 2.5.1 SCSI-3 Option
      • 2.5.2 SCSI-3 Mixed With SCSI-2 Option
      • 2.6 SCSI Bus Backplane Connection Options
      • 2.6.1 Option I. Transition Module
      • 2.6.2 Option II. Flatcable Connection
      • 2.6.3 Option III. Backplane Connection
      • 2.7 Identification
      • Chapter 3 Installation Procedures
      • 3.1 Introduction
      • 3.2 SCSI Bus ID Selection
      • 3.3 SCSI Bus Termination
      • 3.3.1 Internal Termination
      • 3.3.2 External Termination
      • 3.3.3 Mixing Buses Having Different Widths
      • 3.4 Spindle Sync Option
      • 3.5 Power Supply Considerations
      • 3.5.1 +5Vdc Pins
      • 3.5.2 +12Vdc Pins
      • 3.6 Installation Steps
      • Appendix A Block Diagram
      • Appendix B Component Layout
      • Appendix C List of Components
      • Appendix D Connector Assignments
  • Brand Innovators B.V. BI-0433
    • >Brand Innovators B.V. BI-0433 Block Diagram
    • Brand Innovators B.V. BI-0433
    • manual/bi0433/book_1.htm
      • Chapter 1 General Information
      • 1.1 Introduction
      • 1.2 Features
      • 1.3 General Description
      • 1.4 Ordering Information
      • 1.5 Related Documents
      • Chapter 2 Specifications
      • 2.1 Introduction
      • 2.2 Components Used
      • 2.3 VMEbus Options
      • 2.4 Input Specifications
      • Chapter 3 Functional Description
      • 3.1 Introduction
      • 3.2 Group Description
      • 3.2.1 Group Input Circuit
      • 3.2.2 Channel Description
      • 3.2.3 Interrupt Capability
      • 3.2.4 Group Operation Modes
      • 3.2.5 Mode Description
      • 3.2.5.1 Counter Mode 0
      • 3.2.5.2 Direction Discriminator Modes 1 to 5
      • 3.2.5.3 Pulse Width Measurement Mode 6
      • 3.2.5.4 Frequency Measurement Mode 7
      • 3.2.6 Reset Operation
      • 3.3 Bus Interrupt Module
      • Chapter 4 Installation Procedures
      • 4.1 Introduction
      • 4.2 Installation
      • 4.3 Address Selection
      • 4.4 Jumper Settings
      • 4.4.1 Jumper JB1 - Access Mode
      • 4.5 Input/Output Connections
      • Chapter 5 Operating Instructions
      • 5.1 Introduction
      • 5.2 Device Group Registers
      • 5.2.1 Channel Registers
      • 5.2.1.1 Channel Counter Registers
      • 5.2.1.2 Enable Index Register
      • 5.2.1.3 Index Status Register
      • 5.2.1.4 Direct Input Register
      • 5.2.1.5 Compare State Register
      • 5.2.1.6 State On Interrupt Register
      • 5.2.1.7 Interrupt Mask Register
      • 5.2.2 Group Fault Delay Register
      • 5.2.3 Group Mode Register
      • 5.2.4 Group Reset Register
      • 5.2.5 Group BIM Control Register
      • 5.2.6 Group BIM Vector Register
      • Appendix A Block Diagram
      • Appendix B Connector Assignments
      • Appendix C Memory Map
• CANbus
  • BI-0501 CGC
    • Brand Innovators B.V. BI-0501
      • >Brand Innovators B.V. BI-0501 Block Diagram
      • Brand Innovators B.V. BI-0501
      • Copyright
• About us
• Contents
• Manuals